Radsatzdrehbank MFD HOESCH
MFD HOESCH
DRH 130 II-k-s
Radsatzdrehbank MFD HOESCH
MFD HOESCH
DRH 130 II-k-s
Baujahr
1970
Angebotstyp
Gebraucht
DATEN ZUR MASCHINE
- Maschinentyp:
- Radsatzdrehbank MFD HOESCH
- Hersteller:
- MFD HOESCH
- Modell:
- DRH 130 II-k-s
- Baujahr:
- 1970
- Zustand:
- einsatzbereit (gebraucht)
- Betriebsstunden:
- 0
PREIS & STANDORT
DETAILS ZUM ANGEBOT
- Inserat-ID:
- A3998641
- Referenznummer:
- 591
- Aktualisierung:
- zuletzt am 09.11.2021
BESCHREIBUNG
MFD HOESCH Rail – Way Lathe
- Make MFD HOESCH - Germany - Typ DRH 130 II – K - S - Age 1965 - Mach.No. s/n100562
- Height of centers : 800 - Rail track gauge : 1.435
- Max. wheel tread Ø. : 1.350 - Min. wheel tread Ø. : 750
- Max. axle length wheel set: 2.350 - Min. axle length wheel set: 2.050
- Max. clamping Ø. : 1.050 - Min. clamping Ø. : 700
- Face plate Ø. : 1.400
Nlgrr
- Speeds. - Ø. Of headstock quills :
- Overall length bed : - Width across bed sideways : - Height of bed to floor :
- Power. 400 V / 90 kW - Weight. Ca. 40 tonn
Please Note: The above information has been obtained to the best of our ability and belief from, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!
- Make MFD HOESCH - Germany - Typ DRH 130 II – K - S - Age 1965 - Mach.No. s/n100562
- Height of centers : 800 - Rail track gauge : 1.435
- Max. wheel tread Ø. : 1.350 - Min. wheel tread Ø. : 750
- Max. axle length wheel set: 2.350 - Min. axle length wheel set: 2.050
- Max. clamping Ø. : 1.050 - Min. clamping Ø. : 700
- Face plate Ø. : 1.400
Nlgrr
- Speeds. - Ø. Of headstock quills :
- Overall length bed : - Width across bed sideways : - Height of bed to floor :
- Power. 400 V / 90 kW - Weight. Ca. 40 tonn
Please Note: The above information has been obtained to the best of our ability and belief from, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!
ANBIETER
MACH4METAL
Ansprechpartner: Herr MACH4METAL MACH4METAL
Transito 21
6909 DA Babberich, Niederlande

Mach4Metal, spezialisiert in Großmaschinen Zerspanung - und Blechbearbeitungsmaschinen kauft und verkauft gebrauchte Metallbearbeitungsmaschinen wie Abkantpressen, Blechscheren, Schwenkbiegen, Laserscheidanlagen, Drehmaschinen, Drehbänke, Fräsmaschinen, Portalmaschinen, Schleifmaschinen, Bohrwerke, Eckold Kraftformer. Auf unserer Internetseite finden Sie mehr Informationen über uns und unsere Maschinen. Wir haben viele Maschinen wie Skoda Drehmaschinen, Bohrwerke, Eckold Fraftformers, Deckel Maschinen, Mazak CNC Maschinen, Trumpf Abkantpressen, Amada Laser sowie Blechrundbiegen von Häusler, Davi, Stölting auf Lager . Auch konventionele Drehmaschinen von Weiler, VDF Boehringer DUE, Heyligenstaedt, Wohlenberg finden Sie bei uns. Wir haben duchgehend eine große Auswahl von T-Nuten Aufspannplatten auf Lager.
Auf unserer Webseite finden Sie unseren aktuellen Lagerbestand
Mach4metal B.V.
Auf unserer Webseite finden Sie unseren aktuellen Lagerbestand
Mach4metal B.V.
Weitere rechtliche Angaben
Article 1 Definitions
The terms used in these general terms and conditions are defined as follows:
General Terms and Conditions: the Terms and Conditions listed below
Seller: MACH 4 METAL B.V.
Buyer: Any natural or legal person who purchases Products from Seller, or with whom Seller enters into an Agreement, or with whom Seller is currently negotiating in order to enter into an Agreement.
Products: All goods Seller will supply or has supplied pursuant to the Agreement.
Quotation: The offer made by Seller.
Agreement: Any Agreement with regard to the sales and delivery of Products by Seller, any supplement or alteration to said contract, as well as all legal acts in the preparation or for the execution of the Agreement.
Parties: Seller and Buyer are jointly referred to as the Parties.
Article 2 Applicability
1. These General Terms and Conditions apply to all (price) Quotations Seller makes and all Agreements between Parties.
2. Seller explicitly rejects all alterations and/or additions to these General Terms and Conditions, unless they were validated and accepted in writing. Furthermore, Seller explicitly rejects the applicability of Buyer’s Sales Conditions and/or general terms and conditions, unless these were validated and accepted in writing.
3. Should one or multiple provisions, or parts thereof, as recorded in these General Terms and Conditions be nullified or be determined to be invalid in any other way, this will not affect the validity of the other general terms and conditions. In that event Buyer is obligated to agree to one or multiple substitute stipulations, which will resemble the original provision(s) as closely as possible in both purpose and tenor.
Article 3 Establishment of the Agreement
1. Any Quotations and (price) tenders made by Seller shall remain free of engagement. Seller may revoke its Quotations at all times, even when a fixed acceptance term is listed in the Quotation. Buyer’s request for a Quotation or the placement of an order without prior Quotation, will be regarded a request for the production of a Quotation.
2. Data as well as information which are included in Quotations, images, catalogues, technical drawings, advice, and any other provided - subsequent - information, explicitly do not bind Seller.
3. All intellectual property rights with regards to the drawings and/or images presented as part of the offer, rest with Seller. Buyer is not allowed to multiply, publicise or copy any images or drawings without prior written permission.
4. Agreements are established by either an order confirmation or an invoice (should this precede the order confirmation) sent by Seller to Buyer.
Article 4 Prices
1. Prices are expressed in Euros and are, unless otherwise specified, exclusive of VAT, other taxes or surcharges, packing/packaging, and transport costs, as it is where it is.
2. Should one or more of the cost factors be altered after the date of the Quotation but before delivery, Seller is entitled to adjust the agreed on price accordingly, this also applies to binding quotations.
Article 5 Payment
1. Payment shall be made within 48 hours after the invoice date, unless otherwise agreed in writing. Payment should be effectively made in the agreed upon currency. Buyer cannot claim settlement and/or deferment.
2. Prior to the observance of its obligations pursuant to the Agreement, Seller is entitled to request proper security to support Buyer’s payment obligations. Buyer’s refusal to provide the requested security entitles Seller to annul the Agreement(s) in writing or - as is its prerogative- to suspend its obligations.
3. Should Buyer not make payment within the agreed on term, he is deemed to be in immediate default which entitles Seller to increase the amount due with either a default interest of 5% per month or the statutory commercial interest rate under article 6:119a BW (Dutch Civil Code), starting on the invoice date (a part of the month counting as a whole), of the gross invoice amount up until the time of full payment.
4. Should Buyer not meet its (payment)obligations, he is obligated to reimburse all (collecting)fees to Seller.
5. In contravention to paragraph 1, payment will be immediately due when the agreed on price (or part thereof) is not paid promptly, when Buyer is in a state of bankruptcy or equal circumstances, requests moratorium, when legal restraint or administration is requested, or when any attachment is placed on Buyer’s property or receivables.
Article 6 - Delivery
1. The delivery period provided by Seller is indicative only. The exceeding of the delivery period will not lead to Seller’s liability without factual proof of default.
2. Delivery of the Products will be made, unless otherwise agreed, ex works. The Products are deemed to be delivered once they have been offered by Seller to Buyer at the agreed on time and location for the first time.
3. Buyer is obligated to take possession of the Products on the agreed on time and place. Any transportation, storage or additional costs relating to Buyer’s not (timely) taking possession of the Products, will be at Buyer’s expense.
4. The risk of the Products transfers, regardless of the actual delivery, to Buyer upon the conclusion of the Agreement.
5. Should Buyer request delivery prior to the lapse of the agreed on delivery time, and to the extent to which such is feasible, all subsequent additional costs Seller incurs are at Buyer’s expense.
Article 7 Retention of Title and Claims
1. The ownership of the Products only transfers to Buyer, regardless of the actual delivery, after all claims Seller has pursuant to the Agreement or any other agreement, on Buyer in exchange for the delivered or deliverable Products, as well as claims with regard to any default in the execution of said agreements, have been settled.
2. Buyer is not entitled to transfer, pledge, encumber, process or in any way dispose of any Products still belonging to Seller, with the exception of actions which are part of Buyer’s normal work or company practice.
3. Should Buyer fail to meet the obligations pursuant to the Agreement or otherwise, or should reasonable doubt arise to his doing so in the future, Seller is entitled to remove, or have removed, from Buyer or third parties keeping said Products in storage for Buyer, the delivered Products on which the abovementioned retention of title applies. Buyer is obligated to cooperate with this process in any way.
4. Buyer is obliged to insure any Products delivered under retention of title and to keep them insured against fire, explosion and water damage and against theft and to present the insurance policy for inspection on Seller’s first request.
6. Upon buying, the buyer must inspect the products, after buying the complete risk will go over to the buyer, products are sold: ‘as is, where is ‘
7. Seller is entitled to start its own investigation into the nature, size and cause of the complaint. Under penalty of lapse of his right to claim, all Products relating to the claim made by Buyer, should be carefully stored and be presented to Seller upon first request or be send back to Seller.
8. Claims cannot be made should the defects be caused by everyday wear and tear.
9. Claims cannot be made with regard to defects caused by any external causes and/or Buyer’s actions or failings. In particular, although not exclusively, claims cannot be made should the defects be caused by improper or careless use and/or storage; heavy loading or unprofessional maintenance; repairs, alterations or removal carried out without explicit approval; non-compliance with the user and maintenance guidelines.
10. Claims cannot be made when the fact that the product does not meet its expectation is the result of any government requirements with regards to the nature or quality of the applied construction or materials. In the event of a change in the current technical opinions in the work field or to the relevant government requirements, a default cannot be attributed to Seller solely on that basis and Buyer is not entitled to make a claim solely as a result of this.
Should Buyer make a claim in compliance with the aforementioned, and should this claim be deemed just by Seller, Seller shall, as is its prerogative, determine whether to replace the affected goods or their affected parts, or reimburse them.
Article 8 - Force Majeure
1. Seller is not obligated to observe its obligations should he be hindered as a result of circumstances beyond his control for which he cannot lawfully, legally or socially be held accountable.
2. In these General Terms and Conditions force majeure comprises of all it includes pursuant to law and jurisprudence, as well as all external causes, whether foreseen or unforeseen, on which Seller has no influence, yet which prevent Seller from meeting his obligations, for instance, though not limited to, strikes at Seller’s company.
Article 9 Liability
1. Buyer is entitled to inspect the Products for any defects prior to purchase. The Products are sold and delivered ‘as is, where is’ at the time of the sale, without any warranty and with the exclusion of the provisions listed in article 7:15 and 7:17 BW (Dutch Civil Code), unless explicitly agreed otherwise. Therefore, Seller is not liable for any known or unknown defaults.
2. Seller is not liable towards Buyer with regard to the presence or absence of a CE marking.
3. Seller is not liable for any direct or indirect damage Buyer suffers, explicitly including although not limited to a loss of profits, loss of income, costs incurred during laying up, consequential loss, bodily injury, all forms of financial loss, as well as any claims by third parties, save in the event of intent or conscious recklessness on the side of Seller or by anyone part of Seller’s management.
4. Furthermore, any liability Seller might have in any circumstance, is limited to the damage covered and actually paid out by its insurance company with a maximum of the covered amount in such events.
5. Moreover, Seller shall, without prejudice to the abovementioned, never be held to any reimbursement of damages in the event the amount of the damage exceeds the amount invoiced by Seller for the Products to which the damage directly relates, exclusive of VAT and any other government levies.
Article 10 Disputes and Applicable Law
1. Dutch law shall exclusively govern all Agreements between Parties which are subject to these General Terms and Conditions. The application of the Vienna Sales Convention is expressly excluded.
2. Any disputes between Parties will be filed with the competent judge in the Arnhem district (in the Netherlands).
The terms used in these general terms and conditions are defined as follows:
General Terms and Conditions: the Terms and Conditions listed below
Seller: MACH 4 METAL B.V.
Buyer: Any natural or legal person who purchases Products from Seller, or with whom Seller enters into an Agreement, or with whom Seller is currently negotiating in order to enter into an Agreement.
Products: All goods Seller will supply or has supplied pursuant to the Agreement.
Quotation: The offer made by Seller.
Agreement: Any Agreement with regard to the sales and delivery of Products by Seller, any supplement or alteration to said contract, as well as all legal acts in the preparation or for the execution of the Agreement.
Parties: Seller and Buyer are jointly referred to as the Parties.
Article 2 Applicability
1. These General Terms and Conditions apply to all (price) Quotations Seller makes and all Agreements between Parties.
2. Seller explicitly rejects all alterations and/or additions to these General Terms and Conditions, unless they were validated and accepted in writing. Furthermore, Seller explicitly rejects the applicability of Buyer’s Sales Conditions and/or general terms and conditions, unless these were validated and accepted in writing.
3. Should one or multiple provisions, or parts thereof, as recorded in these General Terms and Conditions be nullified or be determined to be invalid in any other way, this will not affect the validity of the other general terms and conditions. In that event Buyer is obligated to agree to one or multiple substitute stipulations, which will resemble the original provision(s) as closely as possible in both purpose and tenor.
Article 3 Establishment of the Agreement
1. Any Quotations and (price) tenders made by Seller shall remain free of engagement. Seller may revoke its Quotations at all times, even when a fixed acceptance term is listed in the Quotation. Buyer’s request for a Quotation or the placement of an order without prior Quotation, will be regarded a request for the production of a Quotation.
2. Data as well as information which are included in Quotations, images, catalogues, technical drawings, advice, and any other provided - subsequent - information, explicitly do not bind Seller.
3. All intellectual property rights with regards to the drawings and/or images presented as part of the offer, rest with Seller. Buyer is not allowed to multiply, publicise or copy any images or drawings without prior written permission.
4. Agreements are established by either an order confirmation or an invoice (should this precede the order confirmation) sent by Seller to Buyer.
Article 4 Prices
1. Prices are expressed in Euros and are, unless otherwise specified, exclusive of VAT, other taxes or surcharges, packing/packaging, and transport costs, as it is where it is.
2. Should one or more of the cost factors be altered after the date of the Quotation but before delivery, Seller is entitled to adjust the agreed on price accordingly, this also applies to binding quotations.
Article 5 Payment
1. Payment shall be made within 48 hours after the invoice date, unless otherwise agreed in writing. Payment should be effectively made in the agreed upon currency. Buyer cannot claim settlement and/or deferment.
2. Prior to the observance of its obligations pursuant to the Agreement, Seller is entitled to request proper security to support Buyer’s payment obligations. Buyer’s refusal to provide the requested security entitles Seller to annul the Agreement(s) in writing or - as is its prerogative- to suspend its obligations.
3. Should Buyer not make payment within the agreed on term, he is deemed to be in immediate default which entitles Seller to increase the amount due with either a default interest of 5% per month or the statutory commercial interest rate under article 6:119a BW (Dutch Civil Code), starting on the invoice date (a part of the month counting as a whole), of the gross invoice amount up until the time of full payment.
4. Should Buyer not meet its (payment)obligations, he is obligated to reimburse all (collecting)fees to Seller.
5. In contravention to paragraph 1, payment will be immediately due when the agreed on price (or part thereof) is not paid promptly, when Buyer is in a state of bankruptcy or equal circumstances, requests moratorium, when legal restraint or administration is requested, or when any attachment is placed on Buyer’s property or receivables.
Article 6 - Delivery
1. The delivery period provided by Seller is indicative only. The exceeding of the delivery period will not lead to Seller’s liability without factual proof of default.
2. Delivery of the Products will be made, unless otherwise agreed, ex works. The Products are deemed to be delivered once they have been offered by Seller to Buyer at the agreed on time and location for the first time.
3. Buyer is obligated to take possession of the Products on the agreed on time and place. Any transportation, storage or additional costs relating to Buyer’s not (timely) taking possession of the Products, will be at Buyer’s expense.
4. The risk of the Products transfers, regardless of the actual delivery, to Buyer upon the conclusion of the Agreement.
5. Should Buyer request delivery prior to the lapse of the agreed on delivery time, and to the extent to which such is feasible, all subsequent additional costs Seller incurs are at Buyer’s expense.
Article 7 Retention of Title and Claims
1. The ownership of the Products only transfers to Buyer, regardless of the actual delivery, after all claims Seller has pursuant to the Agreement or any other agreement, on Buyer in exchange for the delivered or deliverable Products, as well as claims with regard to any default in the execution of said agreements, have been settled.
2. Buyer is not entitled to transfer, pledge, encumber, process or in any way dispose of any Products still belonging to Seller, with the exception of actions which are part of Buyer’s normal work or company practice.
3. Should Buyer fail to meet the obligations pursuant to the Agreement or otherwise, or should reasonable doubt arise to his doing so in the future, Seller is entitled to remove, or have removed, from Buyer or third parties keeping said Products in storage for Buyer, the delivered Products on which the abovementioned retention of title applies. Buyer is obligated to cooperate with this process in any way.
4. Buyer is obliged to insure any Products delivered under retention of title and to keep them insured against fire, explosion and water damage and against theft and to present the insurance policy for inspection on Seller’s first request.
6. Upon buying, the buyer must inspect the products, after buying the complete risk will go over to the buyer, products are sold: ‘as is, where is ‘
7. Seller is entitled to start its own investigation into the nature, size and cause of the complaint. Under penalty of lapse of his right to claim, all Products relating to the claim made by Buyer, should be carefully stored and be presented to Seller upon first request or be send back to Seller.
8. Claims cannot be made should the defects be caused by everyday wear and tear.
9. Claims cannot be made with regard to defects caused by any external causes and/or Buyer’s actions or failings. In particular, although not exclusively, claims cannot be made should the defects be caused by improper or careless use and/or storage; heavy loading or unprofessional maintenance; repairs, alterations or removal carried out without explicit approval; non-compliance with the user and maintenance guidelines.
10. Claims cannot be made when the fact that the product does not meet its expectation is the result of any government requirements with regards to the nature or quality of the applied construction or materials. In the event of a change in the current technical opinions in the work field or to the relevant government requirements, a default cannot be attributed to Seller solely on that basis and Buyer is not entitled to make a claim solely as a result of this.
Should Buyer make a claim in compliance with the aforementioned, and should this claim be deemed just by Seller, Seller shall, as is its prerogative, determine whether to replace the affected goods or their affected parts, or reimburse them.
Article 8 - Force Majeure
1. Seller is not obligated to observe its obligations should he be hindered as a result of circumstances beyond his control for which he cannot lawfully, legally or socially be held accountable.
2. In these General Terms and Conditions force majeure comprises of all it includes pursuant to law and jurisprudence, as well as all external causes, whether foreseen or unforeseen, on which Seller has no influence, yet which prevent Seller from meeting his obligations, for instance, though not limited to, strikes at Seller’s company.
Article 9 Liability
1. Buyer is entitled to inspect the Products for any defects prior to purchase. The Products are sold and delivered ‘as is, where is’ at the time of the sale, without any warranty and with the exclusion of the provisions listed in article 7:15 and 7:17 BW (Dutch Civil Code), unless explicitly agreed otherwise. Therefore, Seller is not liable for any known or unknown defaults.
2. Seller is not liable towards Buyer with regard to the presence or absence of a CE marking.
3. Seller is not liable for any direct or indirect damage Buyer suffers, explicitly including although not limited to a loss of profits, loss of income, costs incurred during laying up, consequential loss, bodily injury, all forms of financial loss, as well as any claims by third parties, save in the event of intent or conscious recklessness on the side of Seller or by anyone part of Seller’s management.
4. Furthermore, any liability Seller might have in any circumstance, is limited to the damage covered and actually paid out by its insurance company with a maximum of the covered amount in such events.
5. Moreover, Seller shall, without prejudice to the abovementioned, never be held to any reimbursement of damages in the event the amount of the damage exceeds the amount invoiced by Seller for the Products to which the damage directly relates, exclusive of VAT and any other government levies.
Article 10 Disputes and Applicable Law
1. Dutch law shall exclusively govern all Agreements between Parties which are subject to these General Terms and Conditions. The application of the Vienna Sales Convention is expressly excluded.
2. Any disputes between Parties will be filed with the competent judge in the Arnhem district (in the Netherlands).
Anfrage senden
TELEFON & FAX
Telefon:
+31 316 443 000
Fax: +31316247956
Diese Inserate könnten Sie auch interessieren.
3
Ihre Ansprechpartner in unserem Hause:
Herr: Andre Evering
Herr: Mario Klöver
Herr: Falk Deutsch
Herr: Simon Blank
Im Lieferumfang sind enthalten:
01x Palettenregaltraverse, gebraucht
Materialfarbe: blau
Traversentyp: PT130M
Kastenprofil: 130 x 50 mm
Agraffe: 5 Haken
Raster: 50 mm
lichte Weite: 3.300 mm
max. Belastung pro Traversenpaar
ca. 2.400 kg, bei gleichm. verteilter Last
02x Sicherungsstifte, gebraucht
Ausführung: kompl. verzinkt
Zur Absicherung der Längsträger
gegen unbeabsichtigtes ...
7
DK-Thisted, Dänemark

(Händlerstandort)
gut (gebraucht)
Artikel: D-1035-Doppelschüttgutdosierer mit Gewicht
Edelstahl-Doppelschüttgutdosierer mit Gewicht.
Bexwfumahc
Abmessungen: Wanne L 1800 X B 850 X H 1300 mm
Großer Hub: 460 mm, Kleiner Lift 100 mm, Flug 80 mm
L 2700 + Gewicht 500 mm , Gesamt L 3200 mm
6
Neukamperfehn

gut (gebraucht)
Wir bieten Ihnen hier eine gebrauchte Palettenregaltraverse
des Herstellers Bito zum Kauf an.
Gfsxu3z9
Technische Daten zur Palettenregaltraverse:
Regalsystem: Bito
Typ: PRO
Im Lieferumfang sind enthalten:
01x Palettenregaltraverse, gebraucht
Materialfarbe: blau
Traversentyp: PT130M
Kastenprofil: 130 x 50 mm
Agraffe: 5 Haken
Raster: 50 mm
lichte Weite: 3.600 mm
max. Belastung pro Traversenpaar
2.400 kg, bei gleichm. verteilter Last
02x Sicherungsstifte, gebraucht
Ausführung: kompl. ...
3
Neukamperfehn

gut (gebraucht)
Ihre Ansprechpartner in unserem Hause:
Herr: Andre Evering
Herr: Marcel Brahms
Herr: Simon Blank
Wir bieten Ihnen hier eine gebrauchte Palettenregaltraverse
des Herstellers Redirack zum Kauf an.
Technische Daten zur Palettenregaltraverse:
Regalsystem: Redirack
Im Lieferumfang sind enthalten:
01x Palettenregaltraversen, gebraucht
Materialfarbe: orange
Kastenprofil: 130 x 50 mm
Ausführung: Kopftraversen
lichte Weite: 3.260 mm
max. Belastung pro Traversenpaar
2.500 kg, bei gleich...
5
Neukamperfehn

gut (gebraucht)
Ihre Ansprechpartner in unserem Hause:
Herr: Andre Evering
Herr: Marcel Brahms
Herr: Simon Blank
Wir bieten Ihnen hier eine gebrauchte Palettenregaltraverse
des Herstellers Feralco zum Kauf an.
Technische Daten zur Palettenregaltraverse:
Hersteller: Feralco
Im Lieferumfang sind enthalten:
01x Palettenregaltraverse, gebraucht
Materialfarbe: gelb
Kastenprofil: 130 x 50 mm
lichte Weite: 3.745 mm
Agraffe: 3 Haken
max. Belastung pro Traversenpaar
2.000 kg bei gleichm. verteilter Last
...
3
Nesselwang

2010
wie neu (Ausstellungsmaschine)
60 Tonnen Hydraulikpresse steht da wie neu, wurde nur kurz als Probierpresse verwendet, Tischgröße 1200 x 800 mm inkl. Bandanlage und Richtwerk. Gewicht 14,5 Tonnen. Bei Interesse werden Technische Daten und Betriebsanleitung zugeschickt.
Fh9w87t
4
Deinze, Belgien

(Händlerstandort)
gebraucht
Heavy duty lathe with 4 hardened linear guides
Cbvxicjulf
Ma
6
semi-mobiler Sortiertisch
Bmu7ubzk
mit Zuführband
Luftabscheider
Sortierkabine mit 6 Stationen
overband
arbeitet mit dual power (Diesel oder 100 % elektrisch)
9
Schöppingen

2014
werkstattüberholt (gebraucht)
Angeboten wird ein Winkelwolf Fleischwolf K & G Wetter MWW-130 Bj.2014 mit sortier Einrichtung 2-Gang.
Motor Leistung 19 Kw.50A.400V.
Trichter ca.200L. Siehe Fotos.
Leistung ca. 3500 Kg/h.
Schneidsatz 5 - Teilig Trennsatz .
2xMesser,( Scheiben Neu) E-Wolf. Werkstatt geprüft sofort einsatzbereit.
Ezaxaxr
Weiteres auf Anfrage.
Barzahlung bei Abholung, Vorkasse per Überweisung.
Verkauf nur an Gewerbetreibende. Keine Garantie, keine Gewährleistung.
15
Kantenleimmaschine: Maschine 1
Max. Breite des Paneels: 1600 mm
Max. Vortriebsgeschwindigkeit: 52 m/min
Mxidjg
15
Europa

gut (gebraucht)
Kantenbearbeitungsstraße
Fabrikat: IMA/Bargstedt
Technische Daten:
bestehend aus:
a) Vakuumbeschickungsanlage, doppels.
Fabr. Bargstedt, Typ TBH 22/D/30/12
b) Kantenbearbeitungsautomat, doppels.
Fabr. IMA , Typ COMBIMA/K/II/R75/1220/F/R3
c) Winkelübergabe
Fabr. Bargstedt, Typ TFW 20/A/LL/30/12/L/S
d) Kantenbearbeitungsautomat, doppels.
Fabr. IMA , Typ COMBIMA/K/II/R75/1075/F/R3
a) Vakuumbeschickungsanlage, doppels.
Fabr. Bargstedt, Typ TBH 22/D/30/12
Hmhrty3v
Grubenlos, ...
10
Roreto

sehr gut (gebraucht)
Doppelseitige Solo maschine (oder 1° und/oder 2° maschine in ein Maschinenstrasse)
Kantendicke im Rollen (min/max) mm 0,4 / 3
Giwph3r
Kantedicke im Streifen-Furnier (max) mm 1,3
Platten Dicke (min/max) mm 10 / 45
Arbeitsbreite (min/max) mm 244 / 2300 ca.
Steuerung /Software ICOS Open
Vorschubgeschwindigkeit (m/min) 8 - 40
Keine Übertragung bar (Master & Slave systeme)
Sicherheit und Lärmschutz Kabine
Anschlagnocken versenkbar, Abstand (mm) 270
FORMATBEARBEITUNGS (für jede Seite):
Fügefräsaggreg...
10
Roreto

sehr gut (gebraucht)
DOPPELSEITIGE FORMAT- UND KANTENANLEIMMASCHINEN - Ersten (1.) Maschine in einer Linie
Kantendicke im Rollen (min/max) mm
Kanten Dicke in Leisten / Streifen (min/max) mm
Platten Dicke (min/max) mm 12 - 60
Arbeitsbreite (min/max) mm 1300
Steuerung /Software ICOS open
Vorschubgeschwindigkeit (regelbar) m/min 9 - 45
Keine Übertragung bar (Master & Slave systeme)
Oberdruck keilriemen angetrieben
Nzd3f
FORMATBEARBEITUNGS (für jede Seite):
Fügefräsaggregat 75.30 (Kw 6,6 x 1)
KANTENANLEIM TEIL (für j...
1
Furnierpresse (2.500 x 1.300 mm)
SMA-REF-7035
Kategorie: Furnierpressen
Hersteller: Bürkle
Typ: S 10 250 / 130
Baujahr: 1979
Arbeitsbereich:
2.500 x 1.300 mm
6 Stempel
Zustand:
im Einsatz
testbereit
Standort: Schweiz
Verfügbarkeit: sofort
Cai9k93sop
11
Code: 0681
Marke: MASTERWOOD
Modell: K 23/S
Mehrfachbohrmaschine mit 23 Spannfuttern
Technische Daten:
N° 23 Schnellspann-Futter
45 Grad Drehung der Bohrköpfe
Achsabstand zwischen den Bohrfuttern mm 32
Maximale Bohrtiefe mm 75
Abmessungen des Arbeitstisches mm 1000 x 700
Motorleistung Hp 2,5
Drehzahl des Bohrfutters 2800 U/min
Luftdruck atm 6-8
Gesamtabmessungen mm 1100 x 1300 x 1100 h
Gewicht kg 505
Gfj0tgib
3
Hofkirchen an der Trattnach

2008
sehr gut (gebraucht)
Die Maschine ist in Betrieb und in einem guten Zustand. Letzter Service war im Mai 2021
Qglef
Die Maschine läuft im durchschnittlich 2h/Tag
Betriebs- und Wartungsanleitung, sowie Aufstellungspläne vorhanden.
EXW-Hofkirchen, ab Werk, unaufgeladen
Zahlungskonditionen:
80% bei Erhalt der Auftragsbestätigung
20% bei Abholung
jeweils sofort netto nach Erhalt der Rechnung
Sicherheitsstandard:
Die Maschine entspricht den europäischen CE-Vorschriften.
Liefertermin: zu vereinbaren, Anlage ab sofort verf...
5
Laufen, Deutschland

(Händlerstandort)
1989
gebraucht
Arbeitsbreite: 2600 mm
W702f8ol
Anzahl der Schleifköpfe: 8 Stck
Motore: 2 x 75 kW + 2 x 132 kW + 2 x 160 kW + 2 x 160 kW
Kallkar, Deutschland

(Händlerstandort)
1987
einsatzbereit (gebraucht)
Kraftstoffart Übrig
ZF Getriebe 16 S 130 für Mercedes, mehrfach vorhanden,
Bedingung für den Kaufabschluss ist eine Geschäft--Gewerbetätigkeit des Käufers und deren entsprechender Nachweis. Bitte übersenden Sie uns nach Abschluss des Kaufvorgangs einen Nachweis Ihrer Geschäft--Gewerbetätigkeit (z.B. Umsatzsteuer-Identifikationsnummer, Gewerbeschein oder Verbands- oder Kammerausweis). Versand-Übergabe erfolgt erst nach Nachweis der Geschäft--Gewerbetätigkeit.
Verkauf und Lieferung erfolgen aus...
7
Malsch, Deutschland

(Händlerstandort)
2004
gebraucht
Raddurchmesser - max. 130 mm
Radbreite 25 mm
Modul - max. 4
Steuerung Siemens 840 D
Spindeldrehzahlen 0 - 30 U/min
Schrägungswinkel - max. +/- 45 °
Radialschlittenweg X 230 mm
Y - Achse ( Ständer - Quer ) +/- 25 mm
z-Weg 150 mm
Hublänge max. 30 mm
Tischdrehzahlbereich 0 - 1000 U/min
Stößelhübe 500 - 2500 Hub/min
Cup2mkl
Gesamtleistungsbedarf 49 kW
Maschinengewicht ca. 11,5 t
Raumbedarf ca. 6,4 x 4,5 x 4,4 m
Serien-Nr. 13216
9
Hersteller (Standort) Ferromatik, (Pomezia Italien)
Modell K-TEC 175-1650 S
Herstellungsjahr 2008
Seriennummer 543534 543535 543536
Betriebsstunden Nicht sicher: etwa 55000-65000 Stunden pro Stück
Cbshzucwjg
Formen NICHT EINGESCHLOSSEN NICHT EINGESCHLOSSEN NICHT EINGESCHLOSSEN
Werkstoff Polypropylen
Endprodukt Schraubkappen für Mundspülungen
Leistung, Drehzahl, Schussgröße, Kavitation usw. Wir haben 32 Kavitäten bei 13,5 Sekunden mit 250 g Schussgröße betrieben (ca. 60-70 kg ...
Unterschleißheim, Deutschland

(Händlerstandort)
2004
gebraucht
Raddurchmesser - max. 130 mm
Radbreite 25 mm
Modul - max. 4
Steuerung Siemens 840 D
Hub bis 30 mm
Schrägungswinkel max. +/- 45 °
Spindeldurchmesser 85 mm
Hubzahl 500 - 2.500 Hub/min
Spindeldrehzahl max. 1.000 U/min.
Tischbohrungsdurchmesser 160 mm
Gesamtleistungsbedarf 48 kW
Maschinengewicht ca. 10 t
Raumbedarf ca. 4,5 x 3,1 x 3,1 m
Nlpgn
Werkstückband EWAB vorhanden
Maschine wurde mit Emulsion betrieben
6
Matelica (MC), Italien

(Händlerstandort)
2002
einsatzbereit (gebraucht)
X-AXIS-VERLAUF: 1020 mm
Y-AXIS-VERLAUF: 610 mm
Z-AXIS-VERLAUF: 560 mm
SPINDEL: 10000 U/min; 11-15 kW
PALLETTE: N.2 ; 1050x550 mm
Bq2bo79m
HOCHDRUCK-KÜHLMITTEL: 15 Bar
WERKZEUGMAGAZIN: KETTENTYP; 40 POSITIONEN
STEUERUNG: FANUC 18M
GEWICHT: 12000 Kg
GESAMTABMESSUNGEN: 4020 x 2660 x 3080 mm
ZUBEHÖR: SPÄNEFÖRDERER ;
4. AXIS-TISCH
PREIS: Noch zu bestimmen
Vorrätig
5
Leipzig, Deutschland

(Händlerstandort)
2000
gebraucht
Arbeitsbreite: 1700 mm
Anzahl der Schleifaggregate: st.
Werkstückstärke max.: 150 - . 4,0 mm
Schleifbandabmessungen: Umlauf mm
Maschinenabmessungen LxBxH: 4,8 x 2,7 x 2,35 m
Gesamtleistungsbedarf: ca. 6,0 kW
Für Holzbearbeitung!
weitere Merkmale:
- pneumatische Bandführung
- Höhenverstellung per Handrad
- NOT-STOP-Schalter
- Schleifwalzenverstellung
- Bandspanner
- Rollenbahnen (Zu- und Abführung je L: 2800 x B: 1700 mm mit je 6 Stück Rollen) motorisch angetrieben
- Bedienung über Schalttafel
-...
2
Kallkar, Deutschland

(Händlerstandort)
1986
einsatzbereit (gebraucht)
Kraftstoffart Übrig
gebrauchtes Mercedes Getriebe
Hersteller: ZF
Cbvugtzeu8
Typ: 16 S 130 EPS
Mercedes Teilnummer: A699 260 5301
ZF Stücklistennummer: 1295 052 377
Bedingung für den Kaufabschluss ist eine Geschäft--Gewerbetätigkeit des Käufers und deren entsprechender Nachweis. Bitte übersenden Sie uns nach Abschluss des Kaufvorgangs einen Nachweis Ihrer Geschäft--Gewerbetätigkeit (z.B. Umsatzsteuer-Identifikationsnummer, Gewerbeschein oder Verbands- oder Kammerausweis). Versand-Übergabe erfolg...
9
Hattingen

1999
gebraucht
Ref.-Nr.: 10003
Marke: FERROMATIK MILACRON
Typ: K 850-S 2F
Baujahr: 1999
Schließeinheit
Schließkraft: 85 ton
Öffnungsweg: 550 mm
Holmmaß (h x v): 420 x 420 mm
Bual9kla
Einbauhöhe min.: 250 mm
Plattengröße (h x v): 640 x 665 mm
Spritzeinheit
Schneckendurchmesser: 35 + 25 mm
Spritzvolumen: 135 + 49 cm³
Spritzgewicht PS: 123 + 44 gr
Spritzdruck: 1964 + 2254 bar
Maße und Gewichte
Abmessung LxBxH: 5 x 1,6 x 2,0 m
Maschinengewicht: 6100 kg
Zusatzinformationen & Extras
Drehteller: inklusive
15
Kühlaggregat
Crepes & Langos Verkaufsanhänger NEU mit Doppel Gas- Profi- Crepes- Eisen, Crepes Verkaufsanhänger. Wir bieten zum Verkauf CREPES Verkaufsanhänger in verschiedenen Ausstattungs- Varianten möglich, extra- leicht, von jedem bequem bewegbar. Profi-Ausstattung, 2x Crepes Platte mit Thermostatischer Regelung Gasbetrieb, Gasflaschenkasten für 2x11kg Gas- Flasche integriert v. außen bedien./ abschließbar, Elektrik: 230V mit Digital Stromzähler, Fi. Schutzschalter, Stromanschluss v. außen, ...
2
Trenčín, Slowakei

(Händlerstandort)
2000
gebraucht
Schliesskraft 1100 kN
Einspritzdruck 1936 bar
Hubvolumen 254 cm3
Cavmpjxrlb
6
Matelica (MC), Italien

(Händlerstandort)
2001
einsatzbereit (gebraucht)
X-AXIS-VERLAUF: 1020 mm
Y-AXIS-VERLAUF: 610 mm
Z-AXIS-VERLAUF: 560 mm
SPINDEL: 10000 U/min; 11-15 kW
Cawz7b9e2p
PALLETTE: N.2 ; 1050x550 mm
HOCHDRUCK-KÜHLMITTEL: 15 Bar
WERKZEUGMAGAZIN: KETTENTYP; 40 POSITIONEN
STEUERUNG: FANUC 18M
GEWICHT: 12000 Kg
GESAMTABMESSUNGEN: 4020 x 2660 x 3080 mm
ZUBEHÖR: SPÄNEFÖRDERER ;
4. AXIS-TISCH
PREIS: Noch zu bestimmen
Vorrätig
11
Weil der Stadt

sehr gut (gebraucht)
Baujahr unbekannt
Zusammentragmaschine in Turmbauweise
1 Zusammentragturm AC 8000 S
1 Zusammentragturm mit 8 Stationen
Rüttelauslage
Überleitung zur Heftmaschine
Heft-Falz-Aggregat SPF 10 II
2 Heftköpfe Hohner Universal 48/5
Schuppenauslage
Qmtsr
Liefertermin: sofort ab Lager
5
Metzingen, Deutschland

(Händlerstandort)
1981
gebraucht
Werkstücklänge 1500 mm
Hub 0 mm
Schwingdurchmesser 500 mm
Gesamtleistungsbedarf 30 kW
Maschinengewicht ca. 8 t
Raumbedarf ca. m
N A G E L
Kurbelwellen - Bandfinishmaschine
Type UF 16 150 K 86 S
Baujahr unbekannt (lt. Elektroplan 05/81 )
Werkstück - durchm. min. / max. 80 - 160 mm
Werkstück-Schwing - Ø ca. 500 mm
Werkstück-Einspannlänge ca. 1.500 mm
Werkstück-Drehzahl stufenlos regelbar (Hydraulikmotor)
Anzahl der Superfinish Einheiten 14
Aufnahme Ø in der Bandführung ca. max. 200 m...
5
Schwäbisch Gmünd

2005
einsatzbereit (gebraucht)
CNC Bearbeitungszentrum (4-Achsig)
CHIRON FZ 08 K S MAGNUM high speed
Baujahr 2005
CNC Steuerung: Siemens 840 D
Verfahrweg X: 300 mm
Verfahrweg Y: 250 mm
B8igo2i3
Verfahrweg Z: 250 mm
Eilgang (X/Y/Z) :40/40/60 m/min
Aufspannfläche
Tisch: Starrtisch
Aufspannfläche :620 x 270 mm
Spindel
Drehzahl: 15.000 U/min
Leistung :7,2 kW
Werkzeugaufnahme :HSK-A 32
Werkzeugwechsler :23 Stationen
Ausstattung
Kühlmittelversorgung
Kühlmittelhochdruck (IKZ)
Gewicht 3400 kg
4
Sägeblattdurchmesser 250 mm
Schnittdurchmesser max. 120 mm
Schnittbereich bei 90 Grad: vierkant max. 120 x 75 mm
Schnittbereich bei 45 Grad: vierkant max. 80 x 75 mm
Drehzahlbereich 40 / 80 U/min
Antriebsmotor 1,1 kW
Motordrehzahl 1410 U/min
Gesamtleistungsbedarf 380 V / 50 Hz
Maschinengewicht ca. 0,5 t
Bt73wmwi
Raumbedarf ca. 1,5 x 1,5 x 2,0 m
Kaltkreissäge - Vertikal mit Unterschrank
7
SOFORT zum Aktionspreis lieferbar!!! Jetzt Preisvorteil sichern - kommen - kaufen - "mitnehmen" Neuer Brenderup 2270 S inkl. Spriegel und Hochplanenaufbau in Blau Techn. Daten Zul. Gesamtgewicht 750 kg ungebremst Nutzlast ca. 535 kg Bereifung R13 78N Ladefläche / Kasteninnenmaße L/B/H 270 x 130 x 105 cm Aufbau und Ausstattung V - Deichsel verzinkt Knott Markenachse verzinkt solide Laufeigenschaft Gummifederprinzip wartungsfrei kpl. feuerverzinkter Rahmen Aufbau Stahl verzinkt robuste und stabile...
15
Hannover

1998
sehr gut (gebraucht)
Hier bieten wir eine gepflegte Spritzgussmaschine an.
Bdoqujf7ke
Wir nehmen auch gerne gepflegte Maschinen ab Baujahr 2005
in Zahlung . Bitte bieten Sie uns Ihre freiwerdenden Maschinen an.
Fabrikat: Ferromatik Milacron
2-Farben mit jeweils 2 zusätzlichen Spritzeinheiten als zusätzliche Alternativen
Maschine verfügt somit über insgesamt 4 Spritzeinheiten
Typ K 85D -S/2F
Steuerung: IQT 44
Baujahr : 1998
Betriebsstunden 32930 h
Schliesskraft: 850 KN
Spritzeinheit horizontal (1. und 2.) 2 ...
4
Wiefelstede, Deutschland

(Händlerstandort)
gebraucht
Stabelektroden 4,0 x 450
-Typ: Phoenix K 90 S
Besegdvcf2
-Preis: pro Paket
-Anzahl: 2 Pakete vorhanden
-Gewicht pro Paket: 6,2 kg
4
Max. Breite des Paneels: 3200 mm
Max. Länge des Paneels: 1300 mm
Max. Vortriebsgeschwindigkeit: 22 m/min
Bvd0hccvu
4
Kuchl

2019
neuwertig (gebraucht)
Felder Formatkreissäge K-540 S
- Schnittlänge 2800 mm
- Schnittbreite 800 mm
- max Sägeblatt Ø 400 mm
- Auslegertisch 1300 mm
- mit Ablänganschlag 2600 mm
- Motorleistung 5,5 kW / 7,5 PS
- Baujahr 2019
Cbj2avuytk